This tutorial makes a crayon wallet with messy pleats perfect for fat little fingers. It may be confusing the first time through, but once you see what you are attempting to accomplish, you’ll find it much easier the next time. It seems long and complicated, but it really is fairly simple! (With all my tutorials, you can use them as you please- just don’t take credit for the design, because that is just wrong. But sell wallets you make, make them as gifts, whatever!)

First, you need to cut your pieces. You can easily make these from fat quarters! (In fact, you can make two wallets with 2 fat quarters.)

• Cut one 6″ x 6″ square of your contrast fabric.

• Cut one 14″ x 5″ rectangle of your contrast fabric.

• Cut two 10″ x 7″ rectangles of your main fabric.

• Cut two 10″ x 7″ rectangles of heavy weight fusible interfacing.

(You’ll also want to consider your closure type. You can sew a ponytail elastic in and sew a button on the front to close it. Or you can sew in two ribbons to tie it closed. You can use ribbon or a fabric tab and add snaps to close. For this particular one, I used snaps and a fabric closure.)

Apply the heavy weight interfacing according to the directions on the interfacing. If you are running low on interfacing, you can just interface one of the large, main rectangles (the 10″ x 7″ ones). But for best results, you’ll want to apply interfacing to both 10″ x 7″ rectangles. (And, of course, you are interfacing the wrong side of the fabric!)

If you are adding a snap, you’ll need to mark the front snap placement. The snap should be 3.5″ from the top (of the right 7″ side) and 1″ in. Mark your spot, use awl or pointed object to poke a hole in the fabric at that spot. Using a snap press or snap pliers, apply a snap to the marked spot with the cap of the snap on the interfaced side (will be the inside) and the snapping part on the right side of the fabric. This 10″ x 7″ rectangle will be the outside of your wallet.

Take the other 10″ x 7″ rectangle, and find the center. (Fold in half and press a crease.)

With the 6″ square and 14″ x 5″ rectangle of contrast fabric, make a half inch double fold hem on one edge. (A 14″ edge of the rectangle.) To make a double fold hem, press down 1″. Turn fabric edge under and press 1/2″ under. Seam is now 1/2″. Sew along the edge to finish.

(Picture showing how to turn the edge under.)

(Picture showing both finished edges. The square will be the top of your paper pocket. The large rectangle will be the open edge of your crayon pocket.)

These pockets are the trickiest part of this whole project. It may seem confusing the first time you do it, but it gets easier after that first one. Place your 6″ square pocket face down on your fabric as shown above. Make sure your finished edge is toward what will be the top of your wallet. (Note that in the above picture, it is all upside down since I am sewing the pocket on from the bottom to the top.) Align the pocket so it is about 1/4″ to 1/2″ over the center line. (That crease we pressed earlier.) Sew down the center line, joining the two fabrics. Only sew to the top (the finished edge) of the paper pocket, making sure you backstitch at the top. (If you are confused about placement, keep reading and I think you’ll figure out where this is going.)

I sew a straight stitch down the center. Then, I zig-zag over the raw edge of the pocket- further securing it and making it look neat and tidy.

As you can see in the picture above, the wrong side of the fabric is showing. We’re going to flip the pocket to the right and it will look fabulous! Keep reading.

Flip the pocket over so the right side is now showing. Line up the edge of the pocket with the edge of your main fabric. Sew the pocket down close to the edge. This seam will get covered later, so don’t worry with backstitching or enclosing the edges. Notice, the square pocket is not a perfect fit. Resist the urge to trim it to lay perfectly flat here. The gap is intentional!

Press all the excess toward the center seam. Now, sew (from bottom to top, parallel with the center line) a straight line forming a 1/2″ (you can estimate) mini pocket on the inside of the paper pocket. (This is going to be for a little pencil.) Make sure you backstitch at the top (finished edge) of the pocket.

The little excess now needs to be flipped or pleated away from the center seam, then basted down as close to the bottom edge as possible. (This seam will be hidden later, so don’t fuss with backstitching or edges.) This makes the little pencil pocket pleated, and gives it room so the pencil goes in and comes out easily, making it easy for fat little toddler fingers to both take it out and put it back. We’ll be using the same “technique” with the crayon pockets.

Place the crayon pocket (the 14″ x 5″ rectangle of contrast fabric that you finished a long edge of) and place it right side up along the left edge of your main fabric (opposite the paper/pencil pocket). Place the finished edge toward the center seam. Sew a straight line from the outer edge to the finished edge in the middle of the pocket to the middle of the main fabric. (see above picture) You don’t have to measure for exact centers, unless you’re obsessive like that. The messy pleating takes care of any small discrepancies in measurement. Make sure you backstitch at the finished edge. (I know this is probably a confusing process the first time through. Once you finish one and see what you are trying to accomplish, you’ll find it simple the next time around.)

(Picture of the finished center seam of the crayon pocket.)

Line up the edges of the crayon pocket. Note, the excess fabric is intentional. You’ll need it. Sew close to the edge, securing the edges of the pocket. Note that this seam will be hidden later, so there is no need to backstitch or finish the edges of this seam. Just stay as close to the edge as possible while sewing. Do the same with the other side.

Now your crayon pocket will look like this! See all that “extra” fabric just hanging around? Let’s keep going and make this thing look like something you might use.

Now, you’re going to take it from half to fourths. Eyeball about halfway between the center seam and the edge, pushing the fabric equally toward the center seam and edge seam. If you’re super obsessive, you can measure, but it won’t matter. And if you’re not quite sure, always err toward the center, since the edge will have more removed by seam allowances later. Sew from the outer edge to the finished edge, backstitching at the finished edge. Repeat on the other side!

Now your crayon pocket is looking like this. Fun, no? Reminds me of two seagulls holding hands or golden arches side by side or… okay, let’s just move one.

Now, we’re going to halve our fourths, creating eighths! Oh, fun with fractions! Stitch a seam halfway between each forth, pushing the excess fabric equally in opposite directions. Remember to backstitch at the finished edge. (This edge will take a lot of wear from little ones getting crayons in and out of the pocket, so make sure they are secure! Think of their sad little faces when they bust a seam trying to get their pudgy little fingers all the way down in that little pocket. Now, make sure that doesn’t happen!) Continue between each forth (erring toward the center seam, if necessary), making 8 little lumps.

Your creation should now look something like this. Now, we get to messy pleats!!!

Take your iron, and just press those little lumps in any direction they want to go. The only consideration you must take when making these messy pleats, is in making sure the edge pleats go toward the center and NOT toward the outer seams. (You don’t want to take away fabric when you finish your seams.)

(A close-up picture of the messy pleats. Note that you can see both the right and left seam edge! The pleats are NOT covering the outer seams.)

Sew (baste) the outer edge of the fabric, securing the pleats. Make sure you stitch as close to the edge as you can.

Pin closure in place on the interior. Pin it 3.5″ down the side. (That would be the halfway point.) For this wallet, I made a cloth tab. (It is long in the picture. I cut it down and finished the edge after sewing everything up.) You can place a ponytail elastic here and sew a button to the front when you are done to close your wallet. You can sew in a ribbon on each side to tie up your wallet. The details are up to you!

Place your two main fabrics, right sides together. Notice that the snap is to the left. If you’re using snaps, you’ll need to keep in mind which way these go, or you’ll end up with snaps in unusable places.

Sew around the edges, using a 1/4″ seam allowance. In the corners, leave your needle down, lift the foot, rotate your work, and continue sewing. Leave a small hole to turn. (I make sure mine is at the top, about the paper/pencil pocket. I don’t like leaving a hole where the pockets are joined.

(A picture of the hole I left.) Clip your corners, so they’ll end up being corners and not large bumps.

Turn your crayon wallet right side out. (I purposefully chose this photo, because people rarely take pictures of those ugly or scary moments in a project when you wonder if you are doing this “correctly.” Turning things right side out is always a scary moment for me because I wonder if the whole thing is going to rip to pieces or, worse, if I have done the whole thing wrong and will find out momentarily that I put something on upside down or something dumb.)

Push out your corners, straighten your work. Press your wallet. Admire it. Smile at realizing you are so very close to being done with this!

Topstitch as close to the edge as you can while maintaining control of your machine! I always start just before the hole to make sure it gets closed up nicely. Make sure the raw edges of the hole are tucked in nicely (and evenly) before you start topstitching. Topstitch around the entire wallet, overlapping about 1/2″ when you come back to where you began. (Leave your needle down when you reach a corner, lift the foot of your machine, turn, put the foot back down, and keep sewing.)

Finish any closure details you need to. In this case, I had to sew up the end of the fabric strip and add a snap closure. (The finishing looks terrible. I should have finished the inside of this edge differently, but whatever. It snaps dang it!)

Here it is all closed up! (I was not entirely pleased with the way this particular wallet turned out. In fact, I won’t be selling this one, since it is well below my personal standards. But you get the picture. What went wrong? I was too concerned with taking nice pictures to properly press and perfect the topstitching, for one. I was too concerned with pictures to make a proper cloth closing tab. But hey, at least I got plenty of pictures, right?!)

And another look at the finished interior. Fill the crayon pockets with 8 crayons.  Put a small pencil (I use Zebra brand mechanical pencils) in the pencil pocket. Place a 3.5″ x 5″ pad of paper in the paper pocket. (Just place the cardboard back in the pocket, leaving the paper available for coloring.) The messy pleats make it really easy for toddlers to get their crayons in and out of the wallet- giving them a good lesson in keeping their own things neat. (I was shocked when my 2 year old, who never puts anything away, sat and put every crayon back in its place before reaching for another.) You can feel free to use, change, or laugh at my design in any way you wish. Happy crafting!

OTHER NOTES FROM THE PARSONAGE POSTS YOU MIGHT ENJOY

• Double Ruffle Pants Tutorial
• Tiered Pants Sewing Tutorial
• Petal Skirt Tutorial
• Wide Leg Ruffle Pants Tutorial

The post Crayon Wallet Tutorial appeared first on Notes From the Parsonage.

A friend of mine asked if I could make her a plastic bag holder. Of course, I accepted! I looked online for a plastic bag holder tutorial or something. But none of them fit what I wanted it to look like. Most of them were just tubes with elastic at the top and bottom. Very basic. I usually like basic, but I thought it needed a little extra oomph!

So, I did what I do. I sat down with my graph paper and sketched out a plan. This plastic bag holder sewing tutorial is another fat quarter project! Yay! (Fat quarters are 18″ x 22″ pieces of fabric, sold at fabric stores that sell quilting fabric.)

I use reusable bags, but always end up with plastic grocery bags anyway! (You know how you forget sometimes– or Instacart brings you round a whole fresh crop of plastic bags!)

You could also use this bag to store other things. (I stuffed one with fabric scraps!)

Cutting the Fabric for Your Plastic Bag Holder

To make a plastic bag holder, you’ll need one fat quarter, a 4″ strip of a contrasting fabric, 2 small (4″ or so) pieces of elastic, and one small piece of ribbon (6″ or so). (You can also make a fabric “loop” to hang the bag by. It is up to you!)

Measure your fat quarter. It should be about 18″ x 22″, but sometimes they are slightly larger. You’ll want to cut your 4″ strip of contrast fabric so you have two 4″ strips to go across each 18″ side. If your fat quarter is 19″, then cut your strips 19″ to fit.

With the right sides together, sew the contrast strip to the main fabric along the 18″ edge. Repeat for the other side.

I serge all my edges, since I am usually selling what I make. If you’ve got a serger, go ahead and finish those edges. If you don’t have a serger, you can omit the finishing if you want, or you can pink or zig-zag the edge. Since this is not a wearable object, or an object that will get much washing (if any) it isn’t necessary to finish the edges at all. So, don’t feel bad if you choose to skip that step!

Ribbon or Fabric Loop to Hang Your Plastic Bag Holder

Pin your ribbon loop (or fabric loop) a couple inches from the top of the main fabric along the 22″ side. (Which is not a 30″ side, since you just attached two 4″ strips to the ends!) If you put your loop too high, you’ll be fighting it while you sew the elastic casing or it will end up on the ruffle. So, try to put it low enough it will be out of the way, but still at the top of the bag. (You can turn the top ruffle down and see where it will hit if that helps you. I just eyeball it and hope for the best!)

Fold your fabric in half long ways (with your contrast fabric on the top and bottom) and sew with right sides together. Serge or finish the edge as you did with the other seam!

Finishing the Top and Bottom of the Plastic Bag Holder

Serge the top and bottom edge of your contrast fabric (you can see above that the edge of the pink fabric is serged). If you want to skip that step, go right ahead!

Now, press the contrast edge in. (See above!) You want to leave about 1/2″ or so of your contrast fabric showing on the front.

(In the photo above, I am showing you the contrast fabric showing on the front.) Repeat for the opposite end. Press it down, leaving about 1/2″ (maybe a little more) showing on the front.

At this point, you’re bag is looking something like this. It reminds me of the cat tunnel project in In Stitches by Amy Butler. (Don’t know what project I’m referring to? It is a tube, much like this, lined with faux fur for your cat to play in.)

Now, we make our elastic casing! Yay! Sew along about 1/2″ from the edge of the contrast fabric. Then sew all the way around, sewing back over your first stitches.

Sew all the way around again, this time sewing as close to the edge as you can. Also, you’ll need to backstitch the ends and leave a small opening (preferably near the back center seam) to guide your elastic through.

Repeat for the other side! Now, you are almost done!

Adding Elastic to Plastic Bag Holder

Grab your two pieces of elastic!

Here is how I thread my elastic. I put a large safety pin along the back end. It keeps the elastic from slipping all the way through. (Believe me, that is a pain!) I attach a small safety pin to the front end (the end I’ll be pushing through the casing).  Make sure your safety pins are firmly attached. It really sucks when a pin slips off because you put it too close to the edge.

Thread your elastic through the casing.

Sew your elastic together by overlapping it and sewing it with an “elastic” stitch. (The awkward looking zig-zag stitch on your machine that is more “lighting bolty” than “zig-zaggy.” If you don’t have that stitch, a small zig-zag will work. (You may have to reset the width of the zig-zag so it fits on the elastic.)

Repeat for the other side!

Flip and Fill Time

Flip it right side out an you’re done! I know, you’re wondering why I didn’t finish closing off those elastic casings! Well, to be honest, it is a pain in the butt and it serves no real purpose. You can fight through it and close them up if you’d like, but I see no reason to. I backstitched the ends, so I made sure it was nice and secure. The elastic is so tight, You’ll find great difficulty stretching it out to sew that little bitty hole closed. And I see no point in closing it. You can if you’d like, I don’t.

See the lovely loop on the back! You can hang it in your pantry or, if you’re like me, you can hang it on your kitchen wall! (Use some snazzy fabrics and you’ll liven your kitchen up!)

This is my favorite aspect of the design! The top and bottom “mouth” of your bag holder have a nice little flirty splash of contrast! I love it!

Go! Make some as gifts, for yourself, or sell some! (Yep. You can feel free to sell anything you make from any of my free designs.) As always, I just ask that you not take credit for the design and that you’d share the free tutorial with others! (No hoarding freeness!) Have fun!

Other Notes From the Parsonage Posts You Might Enjoy

• Half Yard Baby Shower Gift Tutorial
• Easiest Necktie Ever
• Superhero Cape Tutorial
• Cowboy Bib Tutorial
• Crayon Wallet Tutorial

The post Plastic Bag Holder Tutorial appeared first on Notes From the Parsonage.